SUB PRO & SUB ONE – modular formwork for lightweight slabs
Sub is an innovative modular permanent formwork made of recycled plastic, used for the construction of lightweight two-way slabs.
This new element has been completely redesigned by PROJECT FOR BUILDING to deliver higher performance in replacing traditional lightweight fillers such as clay blocks and polystyrene. The elements allow the creation of flat slabs thanks to conical support feet. The soffit of the slab is automatically flat and ready for plastering, without the need for suspended ceilings.
The elements are available as single or double units. The four different heights can be combined with each other to meet a wide range of structural requirements. All pieces are supplied with adjustable feet and spacers.
The SUB element is made from a 100% recycled polyolefin blend.
DOWNLOAD THE SOFTWARE FOR CALCULATING SUB
CONTACT
Production of innovative products for the construction industry, using recycled and regenerated plastics and complete control of the production cycle.
-
Via Fornace, 24050 Mornico al Serio, Bergamo - Italy -
E-mail: info@projectforbuilding.com
-
Tel: (0039) 035 4490 440
-
Fax: (0039) 035 4490 752
For any inquiries, you can contact PROJECT FOR BUILDING by email or phone, or fill out the form and our team will get back to you.
SUB PRO | SUB ONE
ADVANTAGES
SLAB THICKNESS
Reduced slab thickness with the same loads and spans.
INCREASED NUMBER OF FLOORS
Useful height savings on each floor. Possibility to increase the number of floors within the same total building height and buildable envelope.
MATERIAL SAVINGS
Significant reduction in concrete and reinforcing steel consumption thanks to the lower overall weight.
BEAMLESS DESIGN
Spans up to 20 m. No beams between columns. Greater freedom in column layout—even irregular—benefiting architectural design.
LIGHTWEIGHT SLAB
Weight reduction up to 40%. Reduced deflection. Lower loads on columns and foundations.
FEWER COLUMNS
Reduction in number or section of columns, increasing usable floor space.
Construction of a reinforced concrete slab with bidirectional load-bearing capacity, lightened with SUB elements, to be cast in place on suitable horizontal temporary formwork.
The total slab thickness is ... cm, lightened according to the project with SUB recycled plastic elements, size 52x52 cm, height ... cm, with conical support foot facing downward, height ... cm.
Supply of reinforcing steel bars with bidirectional mesh, diameter and spacing according to design loads.
Supply and installation of SUB elements with their respective joint spacers, for the creation of orthogonal beams between voids, according to the preset thickness, ensuring perfect geometry and stability during casting.
Sub is an innovative modular permanent formwork made of recycled plastic, used for the construction of lightweight two-way slabs.
This new element has been completely redesigned by PROJECT FOR BUILDING to deliver higher performance in replacing traditional lightweight fillers such as clay blocks and polystyrene. The elements allow the creation of flat slabs thanks to conical support feet. The soffit of the slab is automatically flat and ready for plastering, without the need for suspended ceilings.
The elements are available as single or double units. The four different heights can be combined with each other to meet a wide range of structural requirements. All pieces are supplied with adjustable feet and spacers.
The SUB element is made from a 100% recycled polyolefin blend.
Construction of a reinforced concrete slab with bidirectional load-bearing capacity, lightened with SUB elements, to be cast in place on suitable horizontal temporary formwork.
The total slab thickness is ... cm, lightened according to the project with SUB recycled plastic elements, size 52x52 cm, height ... cm, with conical support foot facing downward, height ... cm.
Supply of reinforcing steel bars with bidirectional mesh, diameter and spacing according to design loads.
Supply and installation of SUB elements with their respective joint spacers, for the creation of orthogonal beams between voids, according to the preset thickness, ensuring perfect geometry and stability during casting.
Technical data sheets SUB PRO
Technical Data Sheet SUB PRO 08 Technical Data Sheet SUB PRO 10 Technical Data Sheet SUB PRO 12 Technical Data Sheet SUB PRO 14 Technical Data Sheet SUB PRO 16 Technical Data Sheet SUB PRO 18 Technical Data Sheet SUB PRO 20 Technical Data Sheet SUB PRO 22 Technical Data Sheet SUB PRO 24 Technical Data Sheet SUB PRO 26 Technical Data Sheet SUB PRO 28 Technical Data Sheet SUB PRO 30 Technical Data Sheet SUB PRO 32 Technical Data Sheet SUB PRO 34 Technical Data Sheet SUB PRO 36 Technical Data Sheet SUB PRO 38 Technical Data Sheet SUB PRO 40 Technical Data Sheet SUB PRO 42 Technical Data Sheet SUB PRO 44 Technical Data Sheet SUB PRO 50 Technical Data Sheet SUB PRO 52 Technical Data Sheet SUB PRO 60
SOFTWARE
The software meets the design needs of industry professionals involved in the study of bidirectional lightweight slabs using the Sub Pro / Sub One system, providing the data required to correctly carry out structural pre-dimensioning analysis of the slab.
DOWNLOAD SOFTWARE
BIM / CAD
Un modello digitale 3D che contiene tutte le informazioni sul prodotto, le sue caratteristiche fisiche e funzionali, che viene utilizzato dalla progettazione alla manutenzione dell’opera.
Project For Building offre una libreria BIM e CAD dei suoi prodotti completa e aggiornata, a disposizione di tutti.
